Find the leak. Protect the product.
Whether you are validating a package seal, finding a blocked pathway or checking a sealed component, TME provides quantitative leak, flow, burst, creep, occlusion and vacuum decay testing. FITCO helps Indian laboratories and production teams define the method, select the system and support it through installation, training and calibration.
- Packages and componentsFlexible test scope
- ISO and ASTMStandards aligned methods
- Across IndiaLocal application and service
Start with the failure you need to detect.
Define the sample, expected failure, pressure or vacuum range, smallest relevant leak, cycle time and required record. Those details determine the right TME configuration.
Do you need to test package seals?
Measure burst strength, pressure retention and leak performance on flexible and rigid packaging.
Do you need one system for several methods?
Combine leak, flow, occlusion and vacuum decay when one laboratory handles varied samples.
Do you need dependable production testing?
Use stored programs and clear pass and fail decisions for repeatable routine checks.
Three platforms. One clear route to the right test.
Compare the sample type, failure mode, pressure range, sensitivity, cycle time and data needs before choosing a system.
Configurations vary by application. FITCO can review your sample and method before quotation.
TME BT Integra Pack
Apply controlled pressure to flexible and rigid packs, then review burst, creep or leak results for seal and package integrity decisions.
- 0.001 psigLeak resolution
- Up to 100 psiBurst pressure
- ISO 11607Key standard
TME WORKER Integra
Combine pressure based leak testing, mass flow measurement, occlusion and vacuum decay in one programmable instrument.
- 0.0001 psigPressure resolution
- 10,000 SCCMMaximum flow
- IEC 60529IP67 support
TME WORKER Leak and Flow
Run routine pressure decay, vacuum decay, flow and occlusion checks with stored programs, clear decisions and recorded results.
- Up to 300 psigPressure range
- 100 programsStored methods
- 5,000 resultsData storage
A useful result starts before the test begins.
The instrument must match the sample, connection, failure mode and acceptance limit. Defining these together reduces setup uncertainty and makes results easier to repeat.
- ISO 11607
- ASTM F1140
- ASTM F2054
- ASTM F2095
- ASTM F2096
- IEC 60529
Define the failure
Clarify whether you need to detect a leak, blockage, weak seal or burst point.
Set the test conditions
Confirm pressure, vacuum, flow, dwell time and the required measurement sensitivity.
Match the fixture
Present the package or component consistently so the connection does not control the result.
Plan the record
Decide how operators will review, store and export results for quality decisions.
One team from application review to service.
FITCO supports TME users across India from the first sample review through selection, installation, operator training, calibration and AMC support.
Talk to an applications engineerApplication review
Share the package, component, method and throughput before equipment selection.
Installation and training
Set up the instrument and help operators understand the method and result.
Calibration support
Maintain measurement confidence with planned calibration and technical support.
Lifecycle guidance
Keep the instrument, fixtures and test method aligned as products and requirements evolve.
See the test sequence before you shortlist.
These demonstrations show package leak detection and precise leak testing with the TME range.
What to confirm before requesting a quotation.
A clear application brief makes the first recommendation more useful.
What is TME?
TME, formerly TM Electronics, is a packaging testing brand within Industrial Physics. It makes leak, flow, burst, creep to failure and vacuum decay testers for package and component integrity.
Can I buy TME products in India?
Yes. FITCO supplies, installs, calibrates, trains and provides AMC support for TME and Industrial Physics instruments across India.
Which TME instruments are available?
The range includes the TME BT Integra Pack for burst, creep and leak testing, the TME WORKER Integra for leak, flow, occlusion and vacuum decay, and the TME WORKER Leak and Flow Tester for production and quality control.
What information should I share before requesting a quotation?
Share the package or component, expected failure, test method, pressure or vacuum range, required sensitivity, daily throughput, fixture needs and how results must be stored or exported.
Bring the package. We will help define the test.
Share the sample, failure mode, pressure or vacuum range, standard, sensitivity, daily throughput and data needs. FITCO will help shortlist the appropriate TME system and fixture approach.